NOG200L Automation
The Nagashima high-precision NOG200 cylindrical grinder is equipped with a high-efficiency automatic loading and unloading unit. On the basis of stable processing without changing the processing accuracy of the precision cylindrical grinder, the double-truss manipulator is equipped with an external connection method. The truss manipulator for machine tools adopts two independently controlled feeding manipulators and unloading manipulators, which are fast, stable and efficient. The truss manipulator for the out-of-machine silo can make the loading and unloading of the machine silo, the feeding and clamping of the machine tool and the machining of the machine synchronously. At the same time, the truss manipulator for the off-machine silo can also complete the detection of the key dimensions of the workpiece outside the machine, and according to the test results Sort the finished products.
1.Online diameter detection
It has the function of diameter test during production, re-test after production and double test which is to make sure the finish parts 100% qualified, the failure parts will be screened and sorted automatically.

This device uses KEYENCE sensor, the detecting precision is 1 um, after comparing with the standard part every time to make a judge if it is within the tolerance. When pass, the part will be put into finished parts receiver box, if fail, the part will be put into waste channel.
2.Loading and unloading device
The parts storage device has a big capacity, long parts feeding circle, non-machine stop loading and up-loading and realizes automatic production.
Multi-layer unit
Loading unit

Un-loading unit

The parts storage device has a big capacity, long parts feeding circle, non-machine stop loading and up-loading and realizes automatic production.
Loading and un-loading cycle time is reduced (≤6S)
It can adjust the manipulator quickly at positions like machine tool machining area, blank parts storage device side loading, un-loading according to different parts. The controller has protection function to the manipulator running which can only working in nominated area, thus to reduce the damage to machine tool due to operating by error.
3.Truss manipulator
Equipped with 2 pairs of truss manipulators which can realize parts testing, storage , moving and grinding parts exchanging at the same time.

The manipulator Max moving speed 60m/min, it can reduce the auxiliary time of loading and un-loading and prevent the long waiting time after machine tool finished production which increased the efficiency.
4.Ensure reliable and continuous processing of cylindrical grinders, cylindricity ≤3μm
Measuring instrument controller

Intermittent surface measuring instrument

Guarantee the cylindrical grinding machine can work continuously, cylindricity≤3μm
5.Micro motor rotor, the best tool for stepping motor rotor grinding

The best grinding machine for Micromotor rotor and stepper motor rotor
项 目Item | 单位Unit | NOG200L自动化 | |||||
基本动作Basic actions | 前后Before and after |
| 手动及自动Manual and automatic | ||||
左右Left and right |
| 手动及自动Manual and automatic | |||||
工作能力Ability to work | 顶尖距Top distance | mm | 220 | ||||
中心高度Center height | mm | 80 | |||||
回转直径Swing diameter | mm | D80 | |||||
砂轮Grinding wheel | 尺寸Size | mm | 最大D255~最小D215*D50.8 | ||||
转速Rotating speed | rpm | 0~3000(无级变速Continuously variable speed) | |||||
砂轮架(前后) | 全程移动量Full movement | mm | 150 | ||||
快速行程Fast trip | mm | 25 | |||||
手动进给Manual feed | 快速进给功能Rapid feed function |
| 标准Standard | ||||
进给方式Feeding method |
| 手动电子手轮可三档位切换Manual electronic handwheel can switch three gears | |||||
手轮每转进给量Handwheel per revolution feed | mm(直径) | 1 | 0.1 | 0.01 | |||
手轮每格进给量Handwheel per grid feed | mm(直径) | 0.01 | 0.001 | 0.0001(0.1μm) | |||
粗、中、精磨削Rough, medium and fine grinding | mm | 任意量设定Any amount setting | |||||
纵向进给磨削Longitudinal feed grinding | 每次进给量Feed per feed | 粗段Thick section | μm | 0.1, 0.2, 0.3, 0.5, 0.7, 1, 1.5, 2, 3, 5, 7, 10,15,20 | |||
中段Middle section | μm | ||||||
精段Fine section | μm | ||||||
进给方式Feeding method |
| 左右两侧或单侧Left and right sides or one side | |||||
无火花研磨次数No spark grinding times | 往复Reciprocating | 0,1,2,4,6, | |||||
工作台 (左右)Workbench (left and right) | 旋转角度Rotation angle |
| 10°(逆时针方向Counterclockwise)~3°(顺时针方向Clockwise direction) | ||||
最大移动量Maximum movement | mm | 360 | |||||
自动进给Automatic feed | 速度范围(选择)Speed range (optional) | m/min | 0~2 | ||||
换向方式Reversing mode |
| 传感器检测方式及设置方式Sensor detection method and setting method | |||||
手动进给Manual feed | 电子手轮Electronic hand wheel | mm | 电子手轮3档倍率切换Electronic handwheel 3 speed switching | ||||
手轮旋转一周Handwheel rotates one week | mm | 10 | 1 | 0.1 | |||
手轮最小刻度值Hand wheel minimum scale value | mm | 0.1 | 0.01 | 0.0001(0.1μm) | |||
头架Head frame | 工件采用两顶尖固 定或三爪卡盘夹持The workpiece is held by two top-fixed or three-jaw chucks | 主轴转速Spindle speed | rpm | 标准配置0~1000无级变速Standard configuration 0~1000 stepless speed change | |||
主轴锥孔Spindle taper |
| MT No.2 | |||||
旋转角度(手动)Rotation angle (manual) |
| 0~60°(逆时针方向Counterclockwise) | |||||
尾座Tailstock | (顶尖座)标配(top seat) standard | 行程Stroke | mm | 20 | |||
锥度Taper |
| MT No.2 | |||||
电机Motor | 砂轮主轴电机Wheel spindle motor | kw | 1.5(伺服电机Servo motor) | ||||
砂轮架前后电机Grinding wheel frame front and rear motor | kw | 0.4(伺服电机Servo motor) | |||||
工作台左右电机Workbench left and right motor | kw | 0.75(伺服电机Servo motor) | |||||
主轴电机Spindle motor | kw | 0.4(伺服电机Servo motor) | |||||
润滑方式Lubrication method |
| 全自动润滑Fully automatic lubrication | |||||
自动化参数 Automation parameter | |||||||
第一组桁架机械手First set of truss manipulators | YL轴 Axis | 最大进给速度Maximum feed rate | m/min | 60 | |||
行程Stroke | mm | 390 | |||||
电机Motor | kw | 0.75(伺服电机Servo motor) | |||||
ZL轴Axis | 最大进给速度Maximum feed rate | m/min | 60 | ||||
行程Stroke | mm | 960 | |||||
电机Motor | kw | 2(伺服电机Servo motor) | |||||
第二组桁架机械手Second group of truss manipulators | YL轴Axis | 两组SMC气缸Two sets of SMC cylinders | m/min | 30 | |||
行程Stroke | mm | 170 | |||||
ZL轴Axis | 最大进给速度Maximum feed rate | m/min | 60 | ||||
行程Stroke | mm | 960 | |||||
电机Motor | kw | 2(伺服电机Servo motor) | |||||
多层料仓Multi-layer silo | XL轴Axis | 最大进给速度Maximum feed rate | m/min | 25 | |||
行程Stroke | mm | 790 | |||||
电机Motor | kw | 400 | |||||
零件Components | 最大重量Maximum weight | kg | 0.5Kg | ||||
最大外径尺寸Maximum outer diameter | mm | D15-D65 | |||||
机床面积Machine area | mm | 2750*2600 | |||||
机床重量Machine weight | kg | 约2000 | |||||
*由于产品不断更新,产品规格如有变化,恕不另行通知。 | |||||||
VIEWO LIST
NOG200L